Trane 14 SEER Air Conditioner Systems Archives | FL Cooling Store

FL Cooling Deep Coil Cleaning

Florida Cooling Store — Thu, 26 Nov 2020 13:59:02 +0000

Everything in your home’s air goes through your AC coil!

Contaminates build up inside the coil. Traditional heating and cooling systems re-circulate the air in a home via supply air ducts and return air ducts. Many homes have inefficient filters, which trap less than 10 percent of the particulate that is circulated in the system. If not trapped by the systems air filter, the particulate accumulates in the HVAC coil and on the internal components of your furnace and blower.

Cleaning your hvac coil eliminates these contaminates with the following benefits:

Safeguard your health by eliminating potential causes of allergies and respiratory problems.
Eliminate the dirt that acts as food for dust mites, bacteria, mold and other microorganisms

Does Your hvac coil Need Cleaning?

Some signs include; reduced air flow in the home.
excessive dusting or sweeping
Black lines or debris around the register
Higher than normal utility bills
Increased allergy signs
Microbial growth due to moisture issues
Musty odors
Recent home remodeling or construction

Benefits of hvac coil deep clean include;
Improved indoor air quality
Reduced respiratory difficulties
Improved energy efficiency
Extend the life of the heating and cooling system

Our Process:
In the hvac coil deep clean process we remove the coil from your air handler, and use a combination of deep clean agents and fin cleaning tools to remove the built up contaminants on and in your coil.

SANITATION SERVICE
We then sanitize the coil withmicrobiostatic Sanitizing Agent Fully approved by the EPA for use in HVAC systems, SaniJet BioStat is effective against bacteria, fungi, mold & mildew.
Premixed in an isopropyl alcohol base, BioStat dries almost instantly on contact, providing a long term biostatic layer of protection.
There are many benefits to having clean hvac coil. You can experience a reduction in common allergy triggers from items such as pollen, mold spores, dander, and dust.

The FL Cooling HVAC Coil Deep Cleaning Cost is $295.00.

Book now to get ahead of the seasonal rush!

Book Your HVAC System Coil Deep Clean Here!

The post FL Cooling Deep Coil Cleaning appeared first on FL Cooling Store.

UVC Dual Light Whole Home IAQ Package

Florida Cooling Store — Fri, 25 Sep 2020 11:35:19 +0000

Germicidal UV Light works with your home’s filtration system 24/7 to optimize indoor air quality by fighting mold and bacteria growth on your systems coil. Kills pathogens, bacteria, viruses, mildew, and mold.

Delta-Plate installation prevents organic matter from growing in drain pan condensate and potentially clogging the drain pan.
Inner surfaces of the cooling coil, where conditions are more favorable for mold growth, are exposed to UV light.
Close proximity of lamp to cooling coil, where conditions are favorable for mold growth, are exposed to UV light.

We pair this awesome technology with an essential, strategically placed, dual active UVC light at the blower outlet. The return side of the evaporator coil is the one place in your home’s air conditioning system that needs constant attention, and maintenance. We have found that when we install this combination of IAQ products in the HVAC system, the air is noticeably cleaner, and fresher smelling. The coil, and system works more efficiently with fewer blocked coils and maintenance issues.

The post UVC Dual Light Whole Home IAQ Package appeared first on FL Cooling Store.

Trane 3.0 Ton 14.5 SEER 4TWR4036G1000* – TEM6A0C36H31S*

Florida Cooling Store — Wed, 19 Aug 2020 16:10:59 +0000

Trane 4TWR4036G1000* – TEM6A0C36H31S*
3.0 Ton XR14 Series 14.5 SEER Heat Pump
with Trane Air Handler R410A refrigerant.
Condenser:
4TWR4036G1000*
Air Handler:
TEM6A0C36H31S*

AHRI: 10055854

HSPF: 9.0
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 3.0 Ton 14.5 SEER 4TWR4036G1000* – TEM6A0C36H31S* appeared first on FL Cooling Store.

Trane 5.0 Ton 14 SEER 4TWR4060G1000- TEM6A0D60H51S

Florida Cooling Store — Wed, 12 Aug 2020 13:28:08 +0000

Trane
4TWR4060G1000*- TEM6A0D60H51S*
5.0 Ton 14 SEER Heat Pump R410A refrigerant.
Condenser:
4TWR4060G1000*
Air Handler:

TEM6A0D60H51S*

AHRI: 8933060

HSPF: 8.5
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 5.0 Ton 14 SEER 4TWR4060G1000*- TEM6A0D60H51S* appeared first on FL Cooling Store.

Trane 5.0 Ton 14 SEER 4TWR4060G1000- TEM6A0C60H51S

Florida Cooling Store — Wed, 12 Aug 2020 13:25:39 +0000

Trane
4TWR4060G1000*- TEM6A0C60H51S*
5.0 Ton 14 SEER Heat Pump R410A refrigerant.
Condenser:
4TWR4060G1000*
Air Handler:

TEM6A0C60H51S*

AHRI: 9105507

HSPF: 8.5
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 5.0 Ton 14 SEER 4TWR4060G1000*- TEM6A0C60H51S* appeared first on FL Cooling Store.

Trane 4.0 Ton 14 SEER 4TWR4048G1000* – TEM6A0C42H41S*

Florida Cooling Store — Wed, 12 Aug 2020 13:22:34 +0000

Trane 4TWR4048G1000* – TEM6A0C42H41S*
4.0 Ton XR14 Series 14 SEER Heat Pump
with Trane Air Handler R410A refrigerant.
Condenser:
4TWR4048G1000*
Air Handler:
TEM6A0C42H41S*

AHRI: 8932951

HSPF: 8.5
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 4.0 Ton 14 SEER 4TWR4048G1000* – TEM6A0C42H41S* appeared first on FL Cooling Store.

Trane 3.5 Ton 14 SEER 4TWR4042G1000* – TEM6A0C42H41S*

Florida Cooling Store — Wed, 12 Aug 2020 13:19:56 +0000

Trane 4TWR4042G1000* – TEM6A0C42H41S*
3.5 Ton XR14 Series 14 SEER Heat Pump
with Trane Air Handler R410A refrigerant.
Condenser:
4TWR4042G1000*
Air Handler:
TEM6A0C42H41S*

AHRI: 8932642

HSPF: 8.5
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 3.5 Ton 14 SEER 4TWR4042G1000* – TEM6A0C42H41S* appeared first on FL Cooling Store.

Trane 3.0 Ton 14 SEER 4TWR4036G1000* – TEM4A0C37S31S*

Florida Cooling Store — Wed, 12 Aug 2020 13:17:10 +0000

Trane 4TWR4036G1000* – TEM4A0C37S31S*
3.0 Ton XR14 Series 14 SEER Heat Pump
with Trane Air Handler R410A refrigerant.
Condenser:
4TWR4036G1000*
Air Handler:
TEM4A0C37S31S*

AHRI: 9968428

HSPF: 8.5
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 3.0 Ton 14 SEER 4TWR4036G1000* – TEM4A0C37S31S* appeared first on FL Cooling Store.

Trane 2.5 Ton 14 SEER 4TWR4030G1000* – TEM6A0B30H31S*

Florida Cooling Store — Wed, 12 Aug 2020 13:12:57 +0000

Trane 4TWR4030G1000* – TEM6A0B30H31S*
2.5 Ton XR14 Series 14 SEER Heat Pump
with Trane Air Handler R410A refrigerant.
Condenser:
4TWR4030G1000*
Air Handler:
TEM6A0B30H31S*

AHRI: 8932433

HSPF: 8.5
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 2.5 Ton 14 SEER 4TWR4030G1000* – TEM6A0B30H31S* appeared first on FL Cooling Store.

Trane 2.0 Ton 14 SEER 4TWR4024G1000* – TEM6A0B24H21S*

Florida Cooling Store — Wed, 12 Aug 2020 13:09:51 +0000

Trane 4TWR4024G1000* – TEM6A0B24H21S*
2.0 Ton XR14 Series 14 SEER Heat Pump
with Trane Air Handler R410A refrigerant.
Condenser:
4TWR4024G1000*
Air Handler:
TEM6A0B24H21S*

AHRI: 8938849

HSPF: 8.5
Heat Kit
Warranty:
10 Year Parts with registration online by customer.
1 Year Labor from Florida Cooling Store

——————————————

Specification Sheets & Brochures:

Manufacturers Specification Sheets:

Condenser: 4TWR4 Condenser Specifications

Air Handler: TEM4 Air Handler Specifications

Product Brochures: Trane Heat Pump Brochure

Product Brochures: Trane Air Handler Brochure

What’s Included Section:

Florida Cooling Store Inc:

New Condensing Unit.(Outside Piece)

New Air Handler Unit.(Inside Piece)

Supplemental Heat Strips.(Sized to your existing electric, dont worry, we ask for your breaker size before we come out.)

New Digital Honeywell Thermostat.(You have a chance to upgrade it with lots of cool features if you want)

Full Installation Package.(Please pick your existing Air Handler Configuration in the options below, and check out the Install Features table below)

Delivery of Factory new equipment to your home on day of installtion.(You can pick your installation date off of our online calendar!)

Factory Warranty of 10 Years on equipment with Registration Online. (Dont worry, we will help you with this, or do it in the office)

Labor Warranty of 1 Year from Florida Cooling Store Inc. We do great work.(It keeps us from having to keep coming back, we love to visit, but everyone is all so busy these days!)

Service After The Sale. (We have our one year labor warranty, but also offer a full Suite Of Maintenance Plans)

Installation Features:

Name of the feature	Example	Default
* The crew shows up on time.	In the time slot of the day of your choice from our install calendar.	X
* Condenser installed at correct manufacturers clearance.	The Condenser needs air to operate.	x
* Old refrigerant flushed using RX11 line flush.	We have to prepare your copper lines for the new environmentally friendly R410A Refrigerant.	x
* Line drier either installed on site, or factory pre-installed.	This is like an oil filter for your system.	X
* All welds electronically checked.	We don’t want any pesky leaks!	x
* Balanced charge, complete startup.	You want the right amount, down to the ounce, to be perfectly comfortable.	X
* Vacuum pulled to 500 microns.	We use electronic micrometers. Kinda fancy.	x
* Plenums mechanically fastened and sealed to air handler.	The Plenum is basically the outlet, and the inlet for your air flow. Pretty important.	x
* Automatic overflow shutoff switch on airhandler.	I bet you know what a leaking air handler will do to your floor or ceiling.	X
* Old equipment hauled away and recycled.	No big pile of trash out by the road!	X
* Job site cleaned up, all debris hauled back to warehouse.	We have been told that its cleaner after we leave. (We not maids, but we respect your home!)	X
* New Air Handler Base, or rebuild existing built in base.	Either way, its up to code, and done to best practices for your existing installation.	X
* New Cladlight Hurricane Condenser Pad, or level existing base.	This is required, and we do not use a plastic pad, no way!	x
*Start up and test system	We will show you how to use your new system.	x
*Warranty Registration	We will make sure you get your new system registered for your 10 year parts warranty!	X

The post Trane 2.0 Ton 14 SEER 4TWR4024G1000* – TEM6A0B24H21S* appeared first on FL Cooling Store.